; The Release Notes of ASPEED iRMP SOC Flash Utility in FreeBSD
;===============================================================================
v.1.20.00: ycchen@122618
01.[New] Add "option=t" to skip verification
02.[Bug] [AST2500] Fixed GPIOAA/AB/AC settings did not work issue
03.[Bug] [AST25000] Add rstflash option for MX25L512 SPI Flash
-------------------------------------------------------------------------------
v.1.19.00: ycchen@091118
01.[Bug] [AST2500] Fixed it may fail to update flash if enable WDT3
02.[Bug] Extend the file name length to 79
-------------------------------------------------------------------------------
v.1.18.00: ycchen@022318
01.[Bug] [AST2500] Fixed Failed to update SYS SPI Flash
02.[New] [AST2500] Support SPI2 flash update with GPIOR2 as CS
03.[Bug] [AST2400/2500] Fixed incorrect GPIO settings through LPC
04.[Bug] Fixed Die Erase failed on some N25Q512 parts
05.[New] Support DYB un-protected for Spansion S25FL128S/256S
-------------------------------------------------------------------------------
v.1.16.01: ycchen@081517
01.[Bug] [AST2050/2100] Failed to update if the flash size is 32MB or above
v.1.16.00: ycchen@080217
01.[New] Support 128/256MB SPI flash
02.[New] Add Warning Message before flashing
-------------------------------------------------------------------------------
v.1.15.00: ycchen@022217
01.[Bug] [AST2400] Fixed WDT2 will use PCLK as reference clock after flashing
02.[Bug] Fixed cannot updade image larger than 32MB
03.[Bug] [AST2400] Fixed failed to update flash if WDT2 triggerred
04.[Bug] Fixed failed to update Spansion S25FL512S flash chip
05.[Bug] Fixed Return Erase Chip OK in HPM mode
-------------------------------------------------------------------------------
v.1.14.00: ycchen@080416
01.[Bug] [AST2400] Fixed it may update to CS1 flash instead of CS0 flash if enable 2nd boot.
-------------------------------------------------------------------------------
v.1.13.00: ycchen@042216
01.[Bug] [AST2300/2400/2500] Fixed BMC fw did not reboot properly by "option=w" if BMC is diabled by h/w strappings
02.[New] Support option to assign device Bus number
-------------------------------------------------------------------------------
v.1.12.03: ycchen@120215
01.[Bug] Fixed return code error for WDT reset only
v.1.12.02: ycchen@11815
01.[Bug] [AST2500] Fixed BMC fw may not boot properly after flashing
02.[Bug] [AST2500] Fixed failed to flash BMC sometimes if enable 2nd boot
v.1.12.01: ycchen@110315
01.[Bug] remove check I2C prompt message to avoid confusing
02.[Bug] Remove LPC port auto detection to avoid to impact 3rd SIO
03.[Bug] Fixed gpio_b/gpio_f command settings not correct issue
04.[New] Avoid to use legacy IO to disable LPC2AHB
05.[Bug] Fixed failed to update SYSSPI flash on some platforms
v.1.12.00: ycchen@011615
01.[New] Support option for WDT reset only
02.[New] Support Gang Block Unlock
-------------------------------------------------------------------------------
v.1.11.01: ycchen@111014
01.[New] [AST2500] Support SPI2Flash for Secure Boot, ryan_chen@103014
v.1.11.00: ycchen@100214
01.[New] [AST2500] Support AST2500
02.[New] Add Input String Option(See ReadMe.txt for detail)
-------------------------------------------------------------------------------
v.1.10.00: ycchen@062014
01.[Bug] [AST2300/2400] Fixed BMC will not reboot properly after flashing system flash
02.[Bug] Fixed Failed to update somtimes with Atmel AT25DF641
03.[New] [AST2300/2400] Support WinbondW25Q257
-------------------------------------------------------------------------------
v.1.09.04: ycchen@062013
v.1.09.03: ycchen@062013
01.[Bug] [AST1010] Fixed failed to update on AST1010
v.1.09.02: ycchen@050713
v.1.09.01: ycchen@020513
01.[New] Support AST1010
v.1.09.00: ycchen@012313
01.[Bug] Fixed if update data region is below than a sector
-------------------------------------------------------------------------------
v.1.08.00: ycchen@121712
01.[Bug] Fixed I2C cause update slow down issue
02.[New] Support Spansion S25FL128/256 256KB sector size parts
03.[New] Support MXIC MX66L512
-------------------------------------------------------------------------------
v.1.07.03: ycchen@102512
01.[Bug] Fixed failed to update SPI flash PCT25VF080B-80-4C-S2AE
02.[Bug] [AST2300/2400] Fixed failed to disable WDT2 before flashing
v.1.07.02: ycchen@101812
01.[Bug] Fixed WDT failed issue with Winbond 25Q256FV
v.1.07.01: ycchen@090612
01.[New] Support Numonyx N25Q512
02.[New] Modify to support MXIC MX25L25635F
03.[New] Support Atmel AT25DF161
04.[New] Support Winbond 25Q256FV
05.[Bug] Fixed BMC cannot reboot properly if using 24bits addressing firmware on 32MB flash chip
06.[New] Support remote update for AST2400 + AST1070 (SPI Flash only)
v.1.07.00: ycchen@080112
01.[New] Support on AST2400
-------------------------------------------------------------------------------
v.1.06.01: ycchen@043012
01.[Bug] Fixed Update Failed Issue through LPC port 0x4E
02.[New] [AST2300] Support Numonyx N25Q256, Spansion S25FL256S
03.[Bug] Fixed return code incorrect if failed to open image file
v.1.06.00: ycchen@040912
01.[New] Add warning message to remind user don't turn off power during update flash by Quanta request, ycchen@011112
02.[New] add delay option and lock p2a scratch for Hwawei platform
03.[Bug] [AST2300] Fixed can't update flash chip is CS >= 2, ycchen@011312
04.[New] [AST2300] Disable 2nd WDT before flashing
------------------------------------------------------------------------------
v.1.05.02: yc_chen@122911
01.[Bug] Fixed didn't show correct flash chip type for MXIC MX25L257
v.1.05.01: yc_chen@110711
01.[Bug] [AST2300] Fixed failed to update SPI flash occasionally if H-PLL from SCU24, ycchen@110711
v.1.05.00: ycchen@110111
01.[Bug] Fixed Spansion S29GL064 8-bits mode can't work on AST2150
02.[New] Support MXIC MX25L256, ycchen@071911
03.[New] Support Spansion S25FL256S
04.[Bug] Fixed SST25VF016B update issue
05.[Bug] [AST2300] Fixed socflash stressed test hanged issue, ycchen@102811
06.[Bug] [AST2300] Fixed failed to update SPI flash occasionally if H-PLL from SCU24, ycchen@103111
07.[New] Add the option of reginit_b & reginit_f
08.[New] [AST2300] Support gpio_b/f for AST2300
------------------------------------------------------------------------------
v.1.04.03: ycchen@052611
01.[Bug] Fixed running socflash cause system hanged if enable VUART, ycchen@052411
v.1.04.02: ycchen@051811
001.[New] Modify Image and Flash Size Check Message by Customer's request
v.1.04.01: ycchen@050611
001.[New] Support SST SPI Flash JTEG ID, ycchen@050511
002.[New] Add Image and Flash Size Check by Customer's request, ycchen@050611
v.1.04.00: ycchen@031711
01.[New] [AST2300] Limit Max. CLK of SPI to 50MHz by H/W Request
02.[New] [AST2300] Improve the update performance through LPC
-------------------------------------------------------------------------------
v.1.03.06: ycchen@012811
001.[New] [AST2300] Use single read as default for MXIC MX25L25635E/MX25L25735E
v.1.03.05: ycchen@010411
001.[New] [AST2300] Support for System SPI Flash
002.[New] Add the option for SPI CLK
v.1.03.04: ycchen@121010
001.[Bug] [AST2300] Fixed update SPI flash failed if CPU CLK is at 408MHz
v.1.03.03: ycchen@110310
001.[Bug] Fixed Twin's CS0 SPI flash issue, ycchen@082010
002.[New] Support MXIC MX25L6445E, ycchen@090610
003.[New] Add for low speed mode (option=x)
004.[New] Add for general SPI flash support
v.1.03.02: ycchen@061510
001.[New] Add AST2300 16bits NOR Flash Support
002.[New] Add GPIO Settings option
v.1.03.01: ycchen@051410
1. First release for FreeBSD

