Member
Статус: Не в сети Регистрация: 03.03.2006 Откуда: Москва
#77 MSI Afterburner – самая известная и широко используемая утилита для разгона видеокарт. Помимо этого, она служит для получения подробной информации об аппаратных компонентах компьютера и предлагает дополнительные функции, такие как регулировка вентиляторов, тестирование производительности, видеозапись.
1. Для разблокировки разгона в файлеMSIAfterburner.cfg (Находится в папке, где установлена программа) необходимо прописать следующие значения: UnofficialOverclockingEULA = I confirm that I am aware of unofficial overclocking limitations and fully understand that MSI will not provide me any support on it UnofficialOverclockingMode = 1 2. Для разблокировки напряжения и его мониторинга в том же файле прописываем следующие значения: UnlockVoltageControl = 1 UnlockVoltageMonitoring = 1 (!)В драйвере Catalyst 12.2+ не хватает пары файлов, скачиваем здесь 3. Программа так же "умеет" отображать энергопотребление CPU и GPU в играх. ~ Для этого в Настройках (Настройки > Мониторинг) нужно активировать пункты "Энергопотребление" и "Энергопотребление ЦП". 4. После перезагрузки или включения компьютера слетает профиль разгона. Как сделать, чтобы он грузился вместе с Windows? ~ Одно из решений тут - настройка автозапуска ~ Или штатный метод попробовать, описанный здесь 5. Выскакивает ошибка "В данный момент невозможно произвести внедрение в Diretc3D12 компоненты. Строго рекомендуется перезапустить приложение" Решение описано в этом посте 6. Шпаргалка по оформлению оверлейного дисплея от камрада y0121ck - ОСНОВЫ и ДОПОЛНЕНИЕ
Member
Статус: Не в сети Регистрация: 03.02.2016 Фото: 7
Подскажите а в afterburner'е возможно изменить максимальное/минимальное значение для напряжения? GTX 770 - в AB регулировка доступна только от -100 до +100mv. Хотя на скринах где-то видел шкалу с абсолютным значением для напряжения. #77 Bios не хочется модифицировать т.к. в случае "недопиталова" не на чем быстро перешить биос(встройка не доступна).
_________________ Ryzen 7 5800x3d CO -30, x570 Aorus Elite, DDR4 16GBx2 Ballistix 3600 cl16, ASUS RTX 3070ti TUF, Define R5, Custom Water loop
Member
Статус: Не в сети Регистрация: 11.11.2002 Откуда: г.Южноукраинск
Аида 64 видит на моей HD7950 датчик GPU и два датчика WRM1 и WRM2. МСИ АВ (как и спидфан) видит только датчик GPU. Как заставить его увидеть датчики WRM1 и WRM2 (питание чипа и памяти).
Member
Статус: Не в сети Регистрация: 07.10.2007 Откуда: Латвия
Vaal-666 писал(а):
Как заставить его увидеть датчики WRM1 и WRM2 (питание чипа и памяти).
Почему ты решил что это так? Судя по форумам нет там датчиков для считывания тобой указанной температуры.
My Asus GTX970 Strix VRM temp is around 100-102C under heavy load. Dear Mr. ,
Thank you for your trust in our ASUS support. My name is Allen and it is my pleasure to help you with the issue.
Please feel free to rate our service according to the solution provided in the questionnaire that will be sent to you shortly after our reply to your inquiry.
I inform you that the maximum temperature for VRM (Voltage regulator module) for Asus graphic cards is 120 degrees Celsius. The cards VRM will work with no issues whatsoever until 100 degrees and it's usually safe to work up to 110 degrees.
On a normal operation, the card's VRM will often reach 100 degrees and this will not affect the longevity of the card.
If you have any further questions, please do not hesitate to contact us.
Best Regards, ASUS Technical Support
Пока погорят элементы питания остальным элементам видеокарты-кирдык.
Member
Статус: Не в сети Регистрация: 04.03.2009 Откуда: самара
Можно ли поднять частоту памяти на 1050 Ti выше 1000? прописал: UnofficialOverclockingEULA = I confirm that I am aware of unofficial overclocking limitations and fully understand that MSI will not provide me any support on it UnofficialOverclockingMode = 1 не помогает, версия 4.3 #77
MSI AB 4.4.0 Beta 2 is uploaded. It contains RTSS 7.0.0 beta 5, which should fix 2 GUI glitches reported by Danil (dr-rus). Benchmark tab using internal RTSS functionality is now available to everyone. Changes requested by gedo (using modern OSD color tags for indicating critical temperature/fan speed limits) are also inside this build. The purpose of publishing MSI AB beta is entirely focused on testing RTSS related changes, however I stared updating documentation/context help as well so all changes are in readme now:
• Added core voltage control for reference design NVIDIA GeForce GTX 1080 Ti series graphics cards • Improved voltage/frequency curve editor for GPU Boost 3.0 capable NVIDIA graphics cards: o Toggling locked curve point state with <L> key is working properly now and no longer resulting in setting a lock to a minimum clock/frequency point o Now you may hold <Alt> key while adjusting the offset of any point with mouse to move the curve up/down. That’s equal to adding fixed offset to each point’s offset • Various parts of hardware monitoring module have been pumped up to improve hardware monitoring usability and flexibility. Some new portions of old good functionality from original RivaTuner are now available in MSI Afterburner: o Added experimental clock monitoring for Intel CPUs o Added asynchronous hardware polling mode. Asynchronous mode is aimed to move whole hardware polling to a separate thread to avoid slowing down MSI Afterburner GUI while polling some performance expensive hardware monitoring sources. Please take a note that the previous synchronous hardware polling mode can be also enabled via configuration file if necessary o Added new “Benchmark” tab allowing you to use hidden RivaTuner Statistics Server’s benchmarking engine, which was previously available to reviewers only. The engine is providing you the following features: - You may define a hotkey for beginning framerate statistics recording. Once the recording begun, it stays active for all subsequently started 3D applications, even after rebooting the system - While recording is active you may enable showing own statistics in RivaTuner Statistics Server to see minimum, average and maximum framerate in the On-Screen Display - While recording is active you may press “Begin recording” hotkey one more time to restart the recording and reset the statistics - While recording is active you may press “End recording” hotkey once to end recording and save benchmark results to a text file, but keep the results shown in On-Screen Display. You may press the hotkey one more time to hide the results from the On-Screen Display - Statistics saved to a benchmark results file includes per-application total benchmarking time, total rendered frames number, global average, instantaneous minimum and instantaneous maximum framerates. Benchmark statistics file can be optionally either overwritten or appended on each recording session - Per-frame frametime statistics is being pushed to a named pipe so reviewers can use their own client software to collect and display it in realtime while any benchmark is running without system slowdown, which is typical for traditional per-frame frametime logging approach o New flexible On-Screen Display customization features powered by RivaTuner Statistics Server’s text formatting tags: - Added On-Screen Display layouts support. Layout selection settings are located in “Monitoring” tab next to “Show in On-Screen Display”, you may select different layouts to change On-Screen Display appearance style. Now you may switch between traditional classic On-Screen Display layout or new modern column-oriented On-Screen Display layout. Power users may customize predefined layouts or create new ones via configuration file if necessary - The maximum text length for “Override group name” setting is no longer limited by 8 symbols. Now you may embed new RivaTuner Statistics Server’s text formatting tags directly into your custom group name, e.g. “<C=FFFFFF>GTX 1080<S=-50>1<S><C>” to display it in On-Screen Display in white color and with 50% size subscript index - Now it is allowed to override group names for “Framerate” and “Frametime” graphs, so you may append default application 3D API <APP> tag with some custom text or replace it completely if necessary - Exactly the same flexible level of On-Screen Display customization output is available to any other RivaTuner Statistics Server client applications like AIDA, HwInfo and others and will be available shortly o Now you may define optional minimum and (or) maximum thresholds for any graph in hardware monitor module to display alarm message in hardware monitor window when some monitored value is beyond the threshold. When modern On-Screen Display layout is selected, such values can also be highlighted by color there • Improved system information window. Now 3D API usage info, x64 and UWP application architecture attributes are displayed for each currently running process in the list of active 3D applications • RivaTuner Statistics Server has been upgraded to v7.0.0
Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 25
Вы не можете начинать темы Вы не можете отвечать на сообщения Вы не можете редактировать свои сообщения Вы не можете удалять свои сообщения Вы не можете добавлять вложения