C:\Users\Alexey>F:\fptw64.exe

Intel (R) Flash Programming Tool. Version: 7.1.20.1119
Copyright (c) 2007-2011, Intel Corporation. All rights reserved.

FPTw64.exe [-H|?] [-VER] [-EXP] [-VERBOSE] [-Y] [-P] [-LIST] [-I]
[-F] [-ERASE] [-VERIFY] [-D] [-DESC] [-BIOS] [-ME] [-GBE]
[-PDR] [-C] [-B] [-E] [-ADDRESS|A] [-LENGTH|L] [-FOVS] [-EX]
[-U] [-O] [-IN] [-N] [-ID] [-V] [-LOCK] [-DUMPLOCK]
[-PSKFILE] [-CLOSEMNF] [-GRESET] [-SPIBAR] [-R] [-VARS] [-COMMIT]
[-COMPARE] [-HASHED]
-H|? Displays help screen.
-VER Displays version information.
-EXP Displays example usage of this tool.
-VERBOSE <file> Display the debug information of the tool.
-Y Do NOT prompt when a warning occurs.
-P <file> Specifies a flash part definition file to use.
-LIST List all SPI devices supported.
-I Displays information about the flash image.
-F <file> Load binary file into flash.
-ERASE Erase the contents of flash.
-VERIFY <file> Compare binary file to flash.
-D <file> Dump flash contents to file or "STDOUT".
-DESC Load/verify/dump Descriptor region.
-BIOS Load/verify/dump BIOS region.
-ME Load/verify/dump ME region.
-GBE Load/verify/dump GbE region.
-PDR Load/verify/dump PDR region.
-C Erase entire flash part.
-B Check to see if the flash part is erased.
-E Do NOT erase area before writing to flash.
-ADDRESS|A <address> Flash address to load/verify/dump file.
-LENGTH|L <length> Number of bytes to load/verify/dump.
-FOVS Displays list of FOVs supported.
-EX Extract variables from SPI flash to a text file.
-U Update Variable.
-O <file> Output param file.
-IN <file> Input param file.
-N <name> Name of variable.
-ID <id> Id of the FOV to be updated.
-V <value> Value for variable.
-LOCK [PDR] Sets SPI flash region access to Intel recommended values
-DUMPLOCK Dumps the current lock settings to screen.
-PSKFILE <file> PSK key file name.
-CLOSEMNF [NO] [PDR] End of Manufacturing. Details on NO & PDR use -exp option
-GRESET [NO] Global reset drives GPIO30 low unless "NO" is provided.
-SPIBAR Display the SPI BAR.
-R <name> Read a variable.
-VARS Display supported variables.
-COMMIT Commit updates to FOVs requiring a FW reset.
-COMPARE <file> Compare variable with expected value filled in a text file
-HASHED Display a variable (from read command) in hashed format.

Below are examples of common command-line input:
fpt.exe -f image.bin
This usage will write the data in the bin file to the SPI flash part
starting at address zero.

fpt.exe -f image.bin -bios
This usage will write the data in the bin file to Bios region of the SPI
flash part.

fpt.exe -u -id 1 -v P@ssword3
This usage will update the MEBx Password FOV with the password provided.
Refer to the fptcfg.ini file for the ids associated to a specific FOV.

fpt.exe -closemnf NO PDR
This usage should be performed at close of manufacturing. It will set
End of Manufacturing and also sets SPI flash region access to Intel
recommended values. The "NO" addition will prevent the system from
doing a global reset following a successful update of the ME
Manufacturing Mode Done, the Region Access permissions, or both.
The "PDR" addition will allow CPUBIOS Read & Write access to the
PDR region of flash.
fpt.exe -lock PDR
This usage will set SPI flash region access to Intel recommended
values. The "PDR" addition will allow CPUBIOS Read & Write
access to the PDR region of flash.
fpt.exe -greset NO
This usage should be used in order to perform a global reset.
The "NO" afterwards will disable the driving of GPIO30 for mobile SKUs.

Using -EXP followed by parameters (without - or / prefix) will display
all supported command-line sequences with the parameters given.